DEMCiflex Dust Filter 140mm Black/White DF0382Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 153 x 153 mmSize (filter): 129 x 129 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
Schwarzer Temperatursensor für Custom-Waküs, mit G1/4-Zoll-Innengewinde, inkl. Adapter auf G1/4-Zoll-Außengewinde, gängiger 2-Pin-Anschluss, voll vergossen und verzinkt
Hard Tube Fitting von EK Water Blocks, für Röhren mit 12 mm AD, Kompatibel zu Röhren aus Acryl / PETG / Kupfer / Messing / Edelstahl, mit optionalen Ringen farblich individualisierbar, 6er-Pack
Verchromtes Wakü-Fitting von Phanteks mit zwei G1/4-Zoll-Gewinden (Male) zum Verbinden zweier GPU-Wasserkühler mit einem Abstand von 16 bis 22 Millimetern
GELID LIQUID 240 AM5 Compatible High Quality Sleeve Tubing Extreme-Cooling Performance Temperature Display Premium Class Radiator Infinite Mirror 750 – 1800 RPM Noiseless Motor Includes: GC-4 – The State of Art Thermal Compound
Good quality doesn't have to cost a fortune as the Rev.3.00 of the Ultra Silent fan series from (((NB))) proves. The ideal compromise between noise level and power together with the great proce have made the BlackSilent fan series the best-selling fan series on the market. With the XLP we bring a PWM-controlled high-powered version which allows fan speed control via a Mainboard according to Intel(c) specifications. The new revision 3.00 with gloss-finished dust-repelling fan blades, NB-SLICS vibration absorbers as well as many improvements in detail and an extended warranty of 3 years! Compare yourself and find out why the BlackSilent fan series is the best-selling fan series! Outstanding quality - developed in Germany! Original (((Noiseblocker))) quality: Powerful PWM-controlled fan - reliable, long-lived and silent Long-lasting silence: Perfectly adapted speed for Power PCs - Outstandingly silent in its class, and that over a long lifespan Highest safety: Almost inaudible and extremely long-lived NB-Longlife floating bearings of modern design and the high-grade NB-EKA motor result in an unbeatable failure rate of only 0,01% Great price & Cool performance Incl. NB-Slics (vibration absorbers) Technical details: Dimensions : 120x120x25mm Weight : 125g Nominal voltage : 12-13,2 V Starting voltage :
The FW81 is a high quality, standard sized 80mm fan designed for optimal performance with low noise profile. It uses the award-wining fan blade design from AP123 with three distinct shape and sizes to create uneven airflow which is capable of reducing noise frequency effectively compared to traditional fan designs. Powered via PWM 4pin connector, the FW81’s speed can be adjusted by supported motherboard or fan controllers to be used for silent running builds or for cooling a high performance machine.SobilikArvuti korpusTüüpVentilaatorVentilaatori läbimõõt8 cmToetatud protsessoripesadEi ole toetatudÜhilduvad protsessoriseeriadEi ole toetatudPöörlemiskiirus (min)1200 RPMPöörlemiskiirus (max)3000 RPMMüratase (aeglane kiirus)15,3 dBMüratase (suur kiirus)29,5 dBMinimaalne õhuvool12 cfmMaksimaalne õhuvool29,5 cfmMinimaalne õhusurve0,45 mmH2OMaksimaalne õhusurve2,9 mmH2OKeskmine tõrkeintervall (MTBF)40000 hToote värvSinine, ValgeMaterjalPlastPinge12Nimivool0,17 AVentilaatori mõõdud (laius x sügavus x kõrgus)80 x 80 x 25 mmVentilaatori kaal73 g
Suurus:120 L x 120 W x 25 H mm tööpinge:3,5-13,8 V testitud:12V õhuvool:98 m3/h õhusurve:1,450 mm/H20 müratase:23,9 dBA kiirus:1500 RPM võimsustarve:1,80 W eestikeelne ülevaade:http://youtu.be/HnuOvu39nqk tootjalehel:http://www.blacknoise.com/en/products/it/17/Noiseblocker-NB_BlackSilentFan_120mm
This temperature sensor is equipped with G1/4" inner threads on both sides to allow maximum flexibility. The temperature sensor can therefore be equipped with most fittings on the market, allowing the use with almost any hose size. The sensor connection cable has a length of 60cm and a 2-Pin connector. Technical specifications: Connection threads: 2x G1/4"Main body: Nickel coated brassCover ring: Delrin Compatible with: aquaduct-versions with external sensor input (360 XT, 720 XT)Sensor Inputs of many Mainboardsaquaero 3.07, aquaero 4.00aquastream XT UltraAlphacool HeatmasterInnovatek Fan-O-MaticLian Li MultipanelScythe KazeT-Balancer
If you want to have the pump with the highest possible throughput for your water cooling system, you should use the Laing D5. But it's not perfect in one respect: the non-standard connections. Like other manufacturers, Bitspower also offers alternative D5 covers. The completely transparent cover, milled from one block of acrylic, has three G1/4" threaded holes and holes for LEDs. The transparent look makes LEDs and coloured coolants particularly effective. Included in delivery are the necessary screws and a sealing ring. Technical Data: Dimensions: 71 x 71 x 32 mm (W x H x D) Material: Acryl Color: Black, Transparent Thread: 3x G1/4" LED Holes: 2x 5 mm, 2x 3 mm Compatibility: Laing D5, Swiftech MCP 655
To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a blood red finish for 1/2 "or 13mm inner diameter tubing. This can be closed temporarily or permanently unneeded hose ends. Since a plug-in connection was installed, any tube thickness or outside diameter can be used. The end itself forms a screwed closure, which is screwed into a G1 / 4 inch thread and isolated by a sealing ring. If necessary, the thread can also be used to tie other components, which requires a normal external thread with G1 / 4 inches. Note: For a better and secure fit of the hose, we recommend the use of a cable tie or hose clamp. Technical details:Material: brassColor: blood redConnections: Plug connection: 13 mm
The Z-Multi Water Tank from Bitspower has two screw-in POM covers, one with only one G1/4" thread and the other with three G1/4" threads. In the cover, where there is only one G1/4" thread, an adapter is already screwed in, which flows in three individual jets against the reservoir when it is used as an inlet. In the cover, with three threads, a flow pipe is installed in one of the threads, which is usually used as an inlet. If the inlet starts from the upper side, i.e. on the opposite side of the flow pipe, the outlet should not be through the flow pipe, as in the case of a water level below the pipe, air would otherwise enter the cooling circuit. Two plugs are included to close the openings that are not used. One plug is shiny silver, while the other is transparent and has a hole for an optional LED illumination. Two clamps are also included to mount the reservoir to the case or something else. Technical Data: Material: Acrylic, POM Acrylic Tube Color: Clear Dimension: 120 x 60 mm (H x Φ, +/-3%) Length without Cover: 100 mm Inner Diameter: 50 mm Thread: 4x G1/4" Scope of Delivery: 1x G1/4" Silver Shining Stop Fitting, 1x G1/4" Silver Shining Aqua-Pipe I, 1x G1/4" Silver Shining Anti-Cyclone Adapter, 1x G1/4" Crystal Stop Fitting I With 5MM LED Hole, 2x Tank Clamp
The Alphacool “Eiszeit” is a compressor cooler with a maximum cooling power of 1500W. Unlike most so-called Chillers or circulating coolers, the Eiszeit has a high-performance integrated pump. Highlights Integrated pump with 10m head and 600L per hour. Cooling power of 1500W Cooling can be regulated in 0.3 Kelvin increments. Large reservoir with 9L capacity All connectors fit standard G1/4” threads With the “Eiszeit”, you get a compressor cooler designed by Alphacool. With it, you can keep your system – or more than one system – at a temperature you pre-set, automatically regulated for you. The Eiszeit has a maximum cooling power of 1500W. Entering your settings is easily done through the Eiszeit’s display, and you can set the temperature in precise increments of 0.3° Kelvin. If necessary, you can reach temperatures far below room temperature. Another highlight is the integrated high-performance pump with a maximum head of 10m. This means a separate pump is no longer necessary. If the pump performance proves to be too strong, a restrictor can be integrated into the cooling loop via a ball valve or check valve. The G1/4” connectors can fit nearly all standard water cooling attachments. This gives the Eiszeit outstanding compatibility compared to other current products like CPU coolers and graphics card coolers. The Eiszeit also has security functions, such as surge protection for the compressor and an alarm indicating the flow rate is too low or the temperature is too high. Using the Eiszeit is relatively simple. After connecting it to the cooling loop, the loop needs to be filled via the fill port on top of the Eiszeit. The integrated reservoir holds 9L; additionally, you will need enough coolant to fill the complete loop. ATTENTION The temperature can NOT be set below 20 ° C. Technical Details Voltage: 230V Frequency: 50Hz Current: 2.4~3.3A Power consumption: 660W Compressor power: 0.49/0.57KW (0.66/0.77HP) Refrigeration capacity: 1.41/1.70KW Refrigerant: R-134a Refrigerant charge: 380g Precision: ±0.3℃ Reducer: Capillary Protection: Surge protection for compressor, flow alarm, high temperature alarm Pump power: 0.03KW Tank capacity: 9L Inlet and outlet: G1/4 Inner threads connector Max. Lift: 10 meters Max. Flow: 10 L/min Net weight: 29Kgs Noise level: 65 db(A) Dimensions (LxWxH): 560 x 280 x 470mm Materials Reservoir: Polypropylene Tube soft: Silicone Tube hard: PU Scope of Delivery Alphacool Eiszeit 2000 Chiller - black Manual in multiple language Alarm output connector UK power plug Download manual: manual Download data sheet: data sheet NOTICE Because all of the Eiszeit’s functions are tested after manufacturing, some coolant does remain in the system when it is shipped. This is NOT grounds for a return and does not indicate that this item is B-stock or an exchanged item. Notice regarding shipping This item can only be shipped through a freight forwarding service. Since shipping costs will vary by distance, online price calculation is not possible at this time. Please give your full telephone number and email address when placing your order. We will contact you after your order is placed. Shipping costs can add up to ca. 25€ within Germany. Freight forwarding costs will be specified during the ordering process. In case of returns This item can only be sent via a freight forwarding service! Should you need to return the item, please make use of a forwarding agency! Items returned to us via parcel service will not be accepted, as shipping them through a parcel delivery service will damage the device!
The two clamp set is suitable for the equalizing tanks of the Z-series from Bitspower. They make it possible to mount the expansion tank individually inside or outside the case, also with the corresponding pump. The set contains two clamps each with four screws and nuts. The holders have an 80mm, 5mm high and 15mm deep base. The clamps themselves are 10mm wide, have an inside diameter of 60mm and an outside diameter of 66mm. Technical Data: Dimensions: 80 x 70 x 15 mm (W x H x D) Inner Diameter Clamps: 60 mm Outer Diameter Clamps: 66mm Material: Plastic Color: Black Compatibility: Bitspower water tanks of the Z-series
Sehr hochwertiger High-End-Kühler Heatkiller IV Pro von Watercool, vernickelter Kupferboden & Acrylgals Deckel, RGB-LED-Beleuchtung, für AMD-Sockel TR4 (Threadripper) und SP3 (Epyc)
SILENTIUMPC Zephyr 140 - 8,9 dBA Product Description SilentiumPC Zephyr 140 - processor cooler Product Type Processor cooler Package Content Screws, silicone pads Fan Diameter 140 mm Fan Height 25 mm Fan Bearing Hydraumatic bearing Rotation Speed 600 rpm Air Flow 47 cfm Noise Level 8.9 dBA Power Connector 3-pin plug Rated Voltage 12 V Dimensions (WxDxH) 14 cm x 14 cm x 2.5 cm Weight 160 g Manufacturer Warranty 2 years warranty
Preces apraksts angļu valodā:Koolance patented quick disconnect no-spill coupling with automatic shutoff. G 1/4 BSPP (parallel) thread male fitting for screwing directly into a water block or other component. It will only fit a Koolance QD3 female quick disconnect.After pulling the ring on the female QDC side, the quick-disconnect fittings will separate. Liquid on both sides will be automatically obstructed with approximately 0.2ml freed. Coolant volume lost upon disconnection will rise with internal pressure higher than 0.5kgf/cm2 (7psi).
Toote kirjeldus inglise keeles:To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a matte black, straight adapter with two G1 / 4-inch external threads. The special feature: The length of the adapter can be flexibly adjusted between 41 and 69 mm (measured without thread). For this purpose, only one nut is loosened, one side pulled out as desired and then fixed again with the union nut. Technical details:Material: brass, matt blackConnections: male thread: 2x G1 / 4 inchLength: 41 - 69 mm (variable)
Fan speed (max): 1500 Fan speed (min): 600 Air flow rates: 70.32 Number of fans: 3 Noise: 30.4 Weight: 558 Other features: Patented TT RGB PLUS Software & App Hydraulic Bearing
Low-Noise-Pumpe von Alphacool und Laing, Schwarzes Messing-Gehäuse (Black Nickel), möglich, 200 l/h und 2,44 m Förderhöhe bei 10 Watt Leistungsaufnahme, Single Edition ohne Aufsatz
Product kirjeldus: Fractal Design Silent seeria R3 - case fan Product Type: Case fan värv: must, valge Fan Diameter: 80 mm Fan kõrgus: 25 mm Fan Bearing: Rifle bearing pöördekiirus: 1600 pööret minutis õhuvool: 20.2 cfm müratase: 18.1 dBA Power ühenduspesa: 3-pin plug nominaalpinge: 12 V mõõtmed (WxDxH): 8 cm x 8 cm x 2.5 cm kaal: 70 g
With the two matt black holders from Bitspower it is possible to install the complete series of D5 pump, D5 top and Z tube reservoir in the case. The mounting kit is compatible with the D5-Top and the 2D5-Top and can therefore be used as an extension or replacement. Technical Data: Colour: Matt Black Compatibility: D5-TOP, 2D5-TOP
