DEMCiflex Dust Filter 140mm White DF0689Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Note:The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): 153 x 153 mmSize (filter): 129 x 129 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: white (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
When putting down, nothing beats smooth and easy. That is why we created the PK-2 thermal compound. The PK-2 thermal compound is a high performance thermal bonding agent specially designed for easy application.PK-2's core feature is its low viscosity, allowing for one to quickly and easily apply the thinnest coat of thermal compound possible.This will get your components up close and personal in no time.Soojusjuhtivus10,2 W/m·KKaal5 g
The nickel-plated adapter in matt black couples two tubes, which do not run on a common straight line, and ensures a bend of 30 degrees at the adapter. Two rubber rings seal both sides. The adapter is especially well compatible with the Crystal Link Tubes from Bitspower. Technical Data: Material: Nickel-Plated Brass Colour: Matt Black Angle: 30 ° Connections: 2x Ø 12 mm
The Alphacool Eisbaer Pro Aurora CPU AIO water cooler is a special development for processors with particularly large CPU dies. These include the AMD Threadripper and Epyc processors and the Intel CPUs for the LGA 3647 and LGA 4189 socket. With the optional XPX Pro AM4 mounting bracket, the Alphacool Eisbaer Pro CPU cooler can also be used on AMD Ryzen processors. Large cooling surface The cold plate bottom covers the entire surface of the respective processors. The area of the cooling fins exceeds all known processor cores with an area of around 55 x 42 mm. This ensures that all hotspots of a CPU are directly covered and thus optimally cooled. With the additionally available AM4 bracket, cooling an AMD Ryzen processor is also child's play. The cooling fins are 0.4 mm thick and also have an optimal distance of 0.4 mm between them. In total there are 58 cooling fins on the bottom of the cooler. The bottom of the cooler is only 3 mm thick, which allows the heat to reach the water and be dissipated as quickly as possible. Copper radiator As per usual with Alphacool, the radiators are made of copper. Alphacool is the first manufacturer worldwide to use copper for all water bearing components such as the antechambers, the cooling fins and the cooling channels to which the fins are soldered. The connection threads are made of brass for strength reasons. In addition, the cooling fins are only lightly painted. On closer inspection the copper shimmers through a little. A thick lacquer coating would result in a reduction of the cooling capacity. The fin density is at optimal 15FPI. Therefore the radiator works perfectly even at low airflow. A too high fin density would require fans with higher speed to achieve the same cooling capacity. A lower fin density would no longer benefit from fast rotating fans. So the golden mean was chosen. Real water cooling The Eisbaer Pro Aurora consists almost entirely of actual water cooling components. The extremely robust and durable TPV hoses are used in the enterprise products for servers and workstations. The hose connections also come from the Enterprise series from Alphacool and use the standard G1/4". This makes the Eisbaer Pro Aurora fully compatible with all common water cooling products. The quick-release fastener allows easy expansion of the AIO with additional components. The most important of these are the prefilled radiators and the Eiswolf GPU AIO water cooling system. Fan and lighting The entire Eisbaer Aurora Pro cooler is equipped with addressable digital RGB LEDs. This gives a real eye-catcher in the Case. The fan used is the Aurora Rise with 140mm. Due to the special blade design, the fan is extremely quiet and the addressable RGB LEDs provide brilliant illumination. The Alphacool Aurora Rise fan convinces with a max. statistical pressure of 2.20 mm/H 2 O and offers a max. air flow of 154.1 m³/h. The PWM control allows the fan to be controlled over a wide speed range. In addition, it offers a zero control. It can therefore be regulated down to 0 rpm and then starts with approx. 350 rpm. Of course all Digital RGB LEDs can be controlled at will. Depending on the controller almost all effects are possible. How to connect everything The fans are normally controlled via a 4-pin PWM connector. An included Y-adapter for the fans makes it easy to connect them to the mainboard. This allows all fans to be controlled and regulated via one connector. Each fan has a 3-pin JST connector including Y-adapter for the LED illumination. This allows the fans to be connected directly together and can also be controlled simultaneously via a controller. For the connection to a typical 3-pin 5V connector a corresponding adapter is included. Alternatively, the included Digital RGB controller can be used. The pump of the Eisbaer Aurora uses a 3-pin Molex connector. This can also be connected to the mainboard. The Eisbaer Pro Aurora is a true multi-talent. Expandable, fully compatible with DIY water cooling components and it is the optimal solution for the most powerful processors on the market. Technical data radiator L x W x H 316 x 144 x 30 mm (+/- 3% in the range of the pre-chambers) Material fins, chambers & channels copper Material threads brass Material outer housing stainless steel G 1/4“ threads 2 x for tubes For fan size 140 mm Fan mounting options 2 x one-sided / 4 x both-sided Technical data cooler and pump L x W x H 64 x 79 x 54,3 mm Number of LEDs 10x Digital RGB LEDs Material cooler bottom Nickel plated copper Material cooler top PMMA Threads 2 x G1/4“ (+ 1x Fillport G1/4“) Pump typ DC-LT 2 Pump speed 2600 rpm (+/- 10%) Head of delivery 0,95 m Maximum flow rate 75 L/h Technical data fans Speed 0 - 2000 RPM Static pressure 2,20 mm H 2 O Air flow rate 154,1 m³/h Fan connector 4-Pin PWM Connection Digital aRGB 3-Pin JST + 3-Pin 5V Dimensions 140 x 140 x 25 mm Compatibility list: - Intel: 1700 / 2011 / 2011-3 / 2066 / 3647 Narrow & Square / LGA 4189 - AMD: AM4 / TR4 / sTRX4 / SP3 / sWRX8
Hard Tube Fitting von EK Water Blocks, für Röhren mit 12 mm AD, Kompatibel zu Röhren aus Acryl / PETG / Kupfer / Messing / Edelstahl, mit optionalen Ringen farblich individualisierbar, 6er-Pack
120-mm-Radiator mit 44 mm Dicke, Finnen und Kanäle aus Kupfer, exklusives Modding-Design, 5x G1/4-Zoll-Anschlüsse, hochwertige Verarbeitung, geeignet für Custom-Loops
High-end in classic design Developed with and for the most demanding customers, the new (((NB))) Premium fan series, equipped with classic frame and rotor, combines the NB-BlackSilentPro series technology with a classic design. The high-grade NB-EKA Plus II drive system and the virtually inaudible NB-NanoSLI bearings ensure exceptionally quiet operation over the whole lifespan. Both are features which before were only available in the highly sophisticated Multiframe reference series. Besides the tasteful design in matte and high-gloss black, the BlackSilentPro fans feature individually expandable cable management and a NB-Silentframe silicone gasket as well as mounting material for vibration- and tool-free installation. Quality designed in Germany! Detailed information: High-quality fibreglass reinforced chassis in classic deign with Antidust Polycarbonate rotor Cable management, plug-in cables, 20+50cm combinable Vibration- and tool-free mounting Extremely low starting voltage Pulse-noise reduced NB-EKAPLus II Wide range drive Highest safety level: Reverse polarity and overload protection, restarting functionality, extremely fail-safe Virtually inaudible bearings Highest quality: Including mounting material and additional NB-Silentframe gasket Technical specifications: Dimensions: 92x92x25mm Colours: Black frame, transparent brown fan blades Nominal voltage: 12V Starting voltage: 5V Control range: 5-13.2V Power consumption: 1.30W Nominal speed: 500-1800rpm (+/- 10%) Airflow: 14m³/h / 8,2CFM - 65m³/h / 37,6 CFM Noise emissions: 3-20 dB(A) MTBF (25°C): 180000hrs Connector: 3-Pin Extent of delivery: 1x Fan
- True Hi-Flow Design.- Hi-Quality Brass Material.- High Durability Nickel Finished In Carbon Black Color.- Hiding O-Ring Design.- The Best Choice Of Water Cooling Temperature Sensor In Stop Fitting Design.Toote värvMust
Full-Block-Wasserkühler von EK Water Blocks, für RTX 3080 und 3090-Grafikkarten im Referenz-Design, schwarzer Acetal-Deckel, Kühlkörper aus hochreinem Kupfer
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. Technical specifications: Base plate material: electrolyte copper Material cover: acrylic glass Cover material: black anodized aluminum Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x mounting material Thermal Grizzly Kryonaut thermal paste
EK Water Blocks EK-Torque STC-16/10 color ring pack of 10, purple. These exchangeable rings for the 16 / 10mm Soft-Tube compression fittings from EKWB are made of aluminum, are available in different colors and give your system a unique look. Compatibility: EK-Quantum Torque STC-16/10 connections Technical specifications: Color Purple Material: aluminum Quantity: 10 pieces
Stylische Sleeves von CableMod, für Hydro-AiOs von Corsair & EVGA & NZXT, Textil-Sleeving aus ModMesh-Material, einfache Installation in wenigen Minuten
Tootja: AKYGA Tootegrupp: ventilaator korpustele Fan's size class: 120 mm ventilaatori laagri tüüp: liugelaager ventilaatori pöördekiirus: -1000 pööret minutis ventilaatori müratase: -20 dB laius: 120 mm kõrgus: 120 mm paksus: 25 mm toite ühenduse tüüp: 3-pin Termistor: Ei vastupidavus: 30000 tundi õhuvool: -1100000 cm3/min LED kogus: 4 tk LED värv: Red Lisaandmed: andmed puuduvad Lisainfo: Product site
The transparent lid made of matt acrylic fits all Protium reservoirs from Singularity. It has four G1/4" connections and, due to its design, can be integrated into the water cooling circuit in a variety of ways. Technical Data Colour: Transparent Material: Acryl (matt) Thread: 4x G1/4" Compatibility: Protium reservoir
Schicker zylindrischer Ausgleichsbehälter, Röhre und Aufsätze aus transparentem Acryl, drei Aufsätze für flexible Anschlussmöglichkeiten, silberne Sicherungsringe aus Aluminium
The Protium reservoir from Singularity Computers is a 200mm tube with a diameter of 60mm. Together with the acrylic attachments, the reservoir The tube itself is made of acrylic and has a total of seven G1/4" ports. Technical Data: Dimensions: 60 x 60 x 239 mm (L x W x H) Diameter: 60 mm Material: Acrylic (lid, base, reservoir), Aluminium (retention rings) Color: Silver, Transparent Threads: 7x G1/4" Scope of Delivery: 1x 200 mm acrylic reservoir 2x Aluminium retention rings 1x 90° quad port cap (bottom) 1x Triple port cap (cover) 1x 16 mm internal acrylic flow standpipe 5x G1/4" stop fittings 2x Silicone O-rings
The vertical bracket from Singularity can be used to mount a Protium series reservoir or pump attachment vertically on a 120 or 140 fan slot of a radiator. It is even possible to mount two reservoirs or pump attachments. Technical Data Colour: Black Material: Aluminium (mounting plates), Stainless Steel (screws) Scope of Delivery: 2x SC Universal 120/140 Back Plate Mounting Plate 2x Vertical mounting plate 4x M4 Button Head Hex (10 mm) 4x M4 Countersunk Hex (10 mm) 4x M4 Washers 4x M4 Nut
The Protium expansion tank from Singularity Computers is a 250mm tube with a diameter of 60mm. Together with the acrylic attachments, the expansion tank reaches a height of 289mm. The tube itself is made of acrylic and has a total of seven G1/4" ports. Technical Data: Dimensions: 60 × 60 x 289 mm (L x W x H) Diameter: 60 mm Material: acrylic (reservoir, lid, base), aluminium (retention rings) Color: transparent, black/li> Ports: 7x G1/4" Scope of delivery: 1x 250 mm acrylic reservoir 2x Aluminium retention rings 1x 90° quad port cap (bottom) 1x Triple port cap (cover) 1x 16 mm internal acrylic flow standpipe 5x G1/4" stop fittings 2x Silicone O-rings
The Alpenföhn Panorama 2 CPU Cooler is a compact and powerful CPU cooler designed with a top-blower design. It features four 6mm heatpipes and a quiet 92mm JetStream fan with PWM connection. It offers high compatibility with sockets and RAM, and has a 95 Watt TDP. The cooler has dimensions of 13cm x 10cm x 13cm and a net weight of 580g.
The CORSAIR iCUE Link LX140 RGB case fan is a high-performance cooling solution designed for enthusiasts seeking efficiency and aesthetics in their computer builds. It features an impressive airflow range of 10.74-84.7 cfm, ensuring that your components stay cool under load. The inclusion of CORSAIR AirGuide technology further enhances cooling by directing the airflow exactly where it's needed the most.For those who demand precision, the fan supports Pulse-width modulation (PWM), allowing for detailed control over fan speeds to strike the perfect balance between cooling and noise. Additionally, the Zero RPM fan mode can completely silence the fan at low temperatures, making it ideal for light computing tasks.Beyond performance, the LX140 RGB elevates the look of any build with its addressable RGB lighting, capable of displaying a wide range of colors and effects that can be synchronized with other iCUE compatible devices. Its magnetic dome bearing design not only contributes to its quiet operation but also ensures longevity. With the included mounting kit, installation is straightforward, making it an excellent choice for both new builds and upgrades alike.
This is the 2nd generation Vector GPU water block from the EK® Quantum Line, designed for EVGA® FTW3 RTX 3070 graphics cards based on the latest NVIDIA® Ampere™ architecture. For a precise compatibility match of this water block, we recommend you refer to the EK Cooling Configurator. An EK Water Block for FTW3 RTX 3070 EK-Quantum Vector FTW3 3070 D-RGB water block is compatible with FTW3 RTX 3070 graphics cards. The Vector water block actively cools the GPU, VRAM, power stages, and chokes in the VRM (voltage regulation module). These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The fin array is populated by 28 microfins with 0.6mm wide microchannels that provide optimal cooling performance, without unnecessary flow restrictions or clogging hazards. The base of the block is CNC-machined out of nickel-plated electrolytic copper, while its top is CNC-machined out of durable POM acetal. These 2nd generation Vector GPU water blocks also feature Acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum Vector FTW3 RTX 3070 D-RGB water block The aesthetic corner end-piece is housing the addressable D-RGB LEDs. This water block boasts a total of 8 individually addressable RGB LEDs, and it is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the EK-Quantum Vector FTW3 3070 water block EK recommends the purchase of a retention backplate, especially for the 3070 models of graphics cards. The backplate improves the overall aesthetics of your graphics cards and also provides additional passive cooling for the GPU core, and backside of the printed circuit board VRM section. Technical Specification Dimensions: (LxHxW) - 314x155x21mm Enclosed EK-Quantum Vector FTW3 RTX 3070 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
Schicker zylindrischer Ausgleichsbehälter, Röhre aus transparentem Acryl, Aufsätze mit mattem Finish, drei Aufsätze für flexible Anschlussmöglichkeiten, schwarze Sicherungsringe aus Aluminium
M.2-2280 SSD passive cooler, with 20 mm aluminum cooling fins, reduces the temperature by up to 40 °C, various thermal pads with different thicknesses, for single and double-sided M.2 SSD storage.
