EK-Loop UNI Pump Reservoir Bracket - 140mm is a mounting adapter for installation of EK D5, DDC, SPC, and VTX pumps and pump-reservoir combo units to any 140mm fan mounting hole pattern (125mm hole spacing). Additionally, it can be used with EK-RES X3 Holder 60mm (2pcs) to mount any reservoir or pump-reservoir combo with a tube of 60mm in diameter. It can be used horizontally or vertically. The offset on the bracket allows for precise placement of the pump or reservoir according to your needs for clearance or easier tube routing. By turning the bracket around the offset can be moved left, right, back, or forward in a horizontal setup, and also left, right, up, or down in a vertical setup. Made from press-bent 1,5mm thick painted steel. The height of the bracket is 11.5mm. This product is compatible with the following EK products: Vertical: EK-Quantum Kinetic TBE D5 series Vertical: EK-XRES Revo D5 series Vertical: EK-XRES X3 series Horizontal: EK-XTOP DDC series Horizontal: EK-XRES SPC Classic series Horizontal: EK-Quantum Kinetic TBE DDC series Horizontal: EK-Quantum Kinetic TBE VTX series Horizontal and Vertical: EK-XTOP Revo D5 series Enclosed: EK-Loop UNI Pump Reservoir Bracket - 140mm 5x polyamide washer M4 0.8mm 5x screws M4x6 DIN7984 5x nut M4 Allen key 2.5mm
The new Eiszapfen PRO hard tube fittings from Alphacool are the next step in development for the familiar Eiszapfen fittings. In the development of the fittings Alphacool concentrated on a specific problem, deforming PETG hard tubes at high temperatures. PETG can start to deform at 60°C. Although such a temperature is usually rarely reached, it can still occur. The Eiszapfen PRO fittings prevent this problem from the outset and hold the tubes in position. The deformation is prevented by the new nylon inserts inside and stabilizes the hard tubes. Furthermore, the fitting still has an O-ring and a compression seal. However, the contact area is much larger than with normal O-rings, which provides a better grip. With the insert and the compression seal, the tube is strengthened from the inside and outside. Even under heavy loads the HardTube does not slip. Alphacool has tested the tensile strength of up to over 8kg, so there is no need to worry about loose tubing. Technical details: Material: brass Colour: chrome Diameter: 22 mm Height: 20 mm Thread: G1/4" Thread length: 5 mm HardTube size: 13 mm Compatibility: PETG, acrylic, brass and glass tubes Weight: 0,023 kg Scope of supply: 1x Alphacool Eiszapfen PRO 13mm HardTube Fitting G1/4 - Chrome Notice: Attention: The manufacturer Mayhems advises that Mayhems fluids, especially the Aurora line of products, have been manufactured and distributed solely for show and modding purposes. These should not be utilized in the system for more than 14 days. We would also like to advise that Mayhems fluids can damage water cooling products, and using Mayhems fluids can thereby void the warranties offered by the following manufacturers: Koolance, Phobya, Alphacool, Aqua Computer, Watercool. Damages such as: clogging, corrosion of aluminium radiators, deterioration of glued containers, etc., are a consequence of the use of Mayhems, but will not be reimbursed by Mayhems. Use is therefore at one’s own risk.
Teaming up eleven stator guide vanes with a specially conceived seven blade impeller the NFF12's Focused Flow? system creates outstanding static pressure and focuses the airflow for superior performance on heatsinks and radiators. At the same time a wide range of advanced aerodynamic design measures second generation SSOBearings and Noctua?s new custom designed PWM IC for fully automatic control guarantee astounding quietness of operation. The NFF12 comes with modular cabling integrated antivibration pads and two speed settings for full flexibility. Its commanding performance exhaustive set of features and Noctua's trusted premium quality make it an elite choice for use on air coolers radiators and other pressure demanding applications.
Dust can be a computer system’s worst enemy as it has the potential to lower cooling performance or cause damage when left overly accumulated. But most fan filters are a hassle to install so SilverStone created an easy to use FF123 fan filter.The FF123 has embedded magnet in its frame so it can be effortlessly attached to any steel chassis without tools. So for those looking for dust reduction for component longevity with increased cooling efficiency, the FF123 is an excellent buy.- Convenient magnetized design for easy installation- Ultra fine filter provides great dust reduction properties- Compatible with most 120mm fans or ventsWeight & dimensionsWidth 120 mmDepth 1.5 mmHeight 120 mmWeight 13.6 gDesignBlackPerformanceSuitable for ChipsetFan diameter 120 mmCompatible processor series No
Tootja: AKYGA Tootegrupp: ventilaator korpustele Fan's size class: 80 mm ventilaatori laagri tüüp: liugelaager ventilaatori pöördekiirus: -2000 pööret minutis ventilaatori müratase: -25 dB laius: 80 mm kõrgus: 80 mm paksus: 25 mm toite ühenduse tüüp: 4-pin Termistor: Ei vastupidavus: 30000 tundi õhuvool: -616 cm3/min LED kogus: andmed puuduvad LED värv: andmed puuduvad Lisaandmed: andmed puuduvad Lisainfo: Product site
After the overwhelming success of the Liquid Pro, the new Coollaboratory Liquid Ultra was developed. Of course the Liquid Ultra is also made of 100% metal, but it has an absolute new usability and offers an outstanding performance. Due to the paste-like texture the application is now very easy. The Coollaboratory Liquid Ultra was optimized for highest performance and optimal usability. The thermal compound consists to 100% of metal, but can be applied very easy with a commercial brush. The processor (Heatspreader) should be cleaned thoroughly before apply the Liquid Ultra, in order to eliminate dirt, old thermal compound or fat. Warning: Please note that you can’t use the Coollaboratory Liquid Ultra with a contact area of aluminum, as it corrodes aluminum. The heatspreader of actual processors consists of nickel-plated copper, not of aluminum. Advice: The application on copper surfaces is a bit easier than on nickel-plated ones, but possible is both. Tähelepanu! Käesolev termopasta ei sobi alumiiniumist jahutitele. Palun veenduge enne ostmist, et toode ikka sobib Teile!
The None Chamfer PETG Link Tube in transparent by Bitspower is made of polyethylene terephthalate, PETG for short. This material is a plastic and is used, for example, for PET bottles. Its strength lies in its high break resistance, easy heatability and high stability. In order to implement them in the system, it is necessary to bend them into shape with heat and cut them to size. As a rule, the None Chamfer does not need to be reworked when it is cut. The tube measures 100cm in length, 12mm on the outside diameter and 10mm on the inside diameter. Only the EML series from Bitspower is compatible as connections. Technical Data: Material: PETG Color: Transparent Outer Diameter: 12 mm Inner Diameter: 10 mm Length: 100 cm Compatibility: EML series Bitspower connectors only
Technical Data: Material: Nickel-Plated Brass Colour: Black Supported Tube: 16/12 mm Thread: G1/4", male Thread Length: 4,5 mm Outer Diameter (Fitting): 23 mm Installed Height: 19 mm Compatible Soft Tubing: PVC, EPDM, Norprene, Silicone and most other flexible tubes
When developing the new BioniX P120, special emphasis was placed on a focused air flow and a high static pressure. The fan guarantees extremely efficient cooling, even with increased air resistance. Numerous improvements, such as engine technology and a newly developed fan design, have noticeably increased the performance of P fans. In internal performance tests, the new P fans leveled out to 28 dB (A) left many competitors behind. Technical Details Fan: 120 mm, 200 - 2,100 rpm (PWM controlled) Air flow: 67.56 CFM / 114.79 m3 / h (@ 2,100 rpm) Noise level: 0.45 sone (@ 2,100 rpm) Static pressure: 2.75 mm H2O (@ 2,100 rpm) Typical voltage: 12 V DC Cable length: 400 mm PST cable length: 50 mm
Alphacool's Eiszapfen series is future-oriented and characterized by excellent workmanship and high flow. Ball valves have always been a flow brake, making life difficult for each pump. Then, Alphacool has developed a ball valve represents no obstacle to a diameter of 10mm. The inside scoop closes absolutely tight, thus preventing further escape of liquid. On both sides all 1/4“ connections with a maximum thread length of 6mm can be screwed. This ball valve is available in two different color versions: Chrome and Deep Black. Technical Details: Dimensions (LxBxW): 35,4 x 36 x 22,7mm Color: Chrome Scope of delivery: Alphacool Eiszapfen 2-way ball valve G1 / 4 - Chrome
RAIJINTEK bringt die neue RBW-Pumpe der ATLANTIS-Serie D5 (mit 200-mm-Reservoir) auf den Markt. Die ATLANTIS D5 RBW vereint eine integrierte und einzigartige Regenbogen-RGB-LED (5V Addressierbar), eine LED-Lichterkappe, die eine erstklassige Lösung für PC-Enthusiasten darstellt. Diese erreicht einen Super-Flow / Fördermenge von bis zu 900 l / h und einen Head-Lift von 4 Metern bei maximaler Geschwindigkeit. Eine hervorragende Leistung, Qualität und Zuverlässigkeit: ANTILA D5 RBW wird aus hochwertigem POM- und PMMA-Material hergestellt und bietet eine kristallklare, stetig, geräuscharme Hochleistungslösung. Mit der ANTILA D5 RBW können PC-Enthusiasten nicht nur ein bemerkenswert performantes Flüssigkeitskühlsystem bauen, sondern auch extern modulare Upgrades für ihren PC kombinieren. Technische Daten: Maße: 80 × 95 × 305 mm (L x B x H) Gewicht: ca. 1260 g Material: POM (Pumpe), Tempered Glass (Reservoir), Aluminium (Stege), Kunststoff (Verschlussstopfen), Stahl (Halterung) Maße: 60 x 60 x 220 mm Ports: 4x G1/4-Zoll Pumpe: Förderhöhe: ca. 3,9 m Maximale Durchflussleistung: 1500 L/h Druck: max. 50 PSI Lager: Keramik Eingangsspannung: 12 V Leistungsstufen: P1 : 1,800 U/min P2 : 2,500 U/min P3 : 3,300 U/min P4 : 4,000 U/min P5 : 4,800 U/min Lautstärke: 40 dB(A) Anschluss: 4-Pin-Molex (Strom), 3-Pin 2510-3P [NA/NA/Fg] Beleuchtung: 12x A-RGB-LEDs 3-Pin RGB (5VDG, 5V)
Tootekood: PH-F140SK_DRGB_PWM_3PGTIN: 886523001713Jahutid ja lisad
Set aus drei Gehäuselüftern, mit digital adressierbarer RGB-Beleuchtung, 140-Millimeter-Format, PWM-gesteuert, 500-1500 U/min, 143,56 m³/h Fördervolumen, inkl. Gummidämpfern und Schrauben
The Protium expansion tank from Singularity Computers is a 150mm tube with a diameter of 60mm. Together with the acrylic attachments, the expansion tank reaches a height of 189mm. The tube itself is made of acrylic and has a total of seven G1/4" ports. Technical Data Dimensions: 60 × 60 x 189 mm (L x W x H) Diameter: 60 mm Material: acrylic (reservoir, lid, base), aluminium (retention rings) Color: transparent, black Ports: 7x G1/4" Scope of delivery: 1x 150 mm acrylic reservoir 2x Aluminium retention rings 1x 90° quad port cap (bottom) 1x Triple port cap (cover) 1x 16 mm internal acrylic flow standpipe 5x G1/4" stop fittings 2x Silicone O-rings
Suurus:92 L x 92 W x 25 H mm tööpinge:3,5-13,8 V testitud:12V õhuvool:50 m3/h õhusurve:0,630 mm/H20 müratase:17,5 dBA kiirus:1500 RPM võimsustarve:0,84 W eestikeelne ülevaade:http://youtu.be/HnuOvu39nqk tootjalehel:http://www.blacknoise.com/en/products/it/16/Noiseblocker-NB_BlackSilentFan_92mm
The new generation of compact fan technology is on the market. Multiframe® fans have completely unique multi-piece chassis, which eliminates vibration already inside of the fan. Therefore resonance throughout the system is reduced. Additional measures for noise reduction such as the use of decoupling kits or insulation mats can be spared with these fans. Depending on the case used, Multiframe® fans are able to reduce the fan-induced noise below the noise from the airflow itself. Multiframe® fans are than "more silent than the air". The new Multiframe® technology has a array of new features: The integrated vibration absorbers are just one of the new features that all contribute to noise reduction. For example the vibration absorbers are wider than the chassis to avoid any contact between case and vibrating parts. The use of massive and heavy materials in the fan leads to a lowering of the noise's frequencies, therefore making it less audible and more comfortable to the human ear. Aerodynamic optimization of frame and strutting also reduce noise by air swirling. This reduces a majority of the noise through airflow and therefore a large part of the overall noise level of the fan. The other parts of the Multiframe® fan series are also on the highest technological level. The improved EKAplus motor is voltage-independent extremely quiet and has an especially low starting voltage. The bearing used is the new NB-NanoSLI® bearing, which is especially quiet and has a long lifespan thanks to a special lubrication system. The fan is also equipped with a reliable auto-restart mechanism and is protected against polarity reversal. Interesting is the fact that the noise level of the Multiframe® series is almost completely dependent from the case they are installed in, as noise produced directly by the is reduced to a minimum and usually below the noise level of the airflow. Thereby these fans are more quiet than their airflow. With this new generation and advance in noise reduction more and more responsibility for noise reduction is in the hands f the case manufacturers. If full advantage is to be taken of these fans an aerodynamically optimized case has to be used, which does not obstruct airflow with tight meshes or other obstructions. Technical details: Dimensions: 80x80x25mm Speed (+- 10%): 1700rpm Airflow: 47m³/h Noise level: 14 dB(A) Voltage range: 4,5-13,8V Starting voltage: 4,5V Power consumption: 1,2W Warranty: 6 years
To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This 45 degree angled G1 / 4 "fitting for 10mm inner diameter (3/8") tubing does not use a union nut, so any tubing thickness and therefore outside diameter can be used. The blood red connection can be turned on the side of the screw thread. This greatly facilitates installation and allows for precise alignment. Note: For a better and safer fit, we recommend using a cable tie or a hose clamp. Furthermore, the rotation function of the connections should always be used in the disassembled state, as this is relatively difficult to move due to the design. When installed, do not apply force to connections to avoid damaging the connectors themselves and the radiators on them. Technical details:Material: brassColor: blood redConnections: Thread: G1 / 4 inch Hose: 10 mm (inside diameter)
The nickel-plated adapter from Bitspower in the color shiny black, has an angle of up to 90 degrees, a G1/4" internal thread and a G1/4" external thread. The special feature of this adapter are the three swivel joints, so that the alignment of e.g. tubes becomes even easier and more flexible. Technical Data: Material: Nickel-Plated Brass Main Color: Shiny Black Angle: up to 90° Thread: 1x G1/4", 1x Inner G1/4" Thread Length: 5 mm
The EK-Annihilator Pro is a CPU cooler which is primarily intended for use in 1U cases in the server area. The copper base ensures optimum heat transfer. The cover is made of black acetal, while the mounting frame is made of aluminium. Due to its design, the CPU cooler requires mainbaords with a hole spacing of 56 x 94 mm. Technical Data: Dimensions: 108 x 86 x 24,2 mm Material Base: Nickel-Plated Electrolytic Copper Material Cover: Acetal Thread: 3x G1/4", 6x G1/8" Compatibility: Intel 3647 Scope of Delivery: EK-Annihilator Pro Narrow ILM, Necessary Mounting Screws/Nuts/Washers, 3x EK plug G1/4", 6x EK plug G1/8", 2x HFB Barb Fitting 6mm, 2x HFB Barb Fitting 10mm, 2x Barb clamp 6mm, 2x Barb Clamp 10mm, 6mm Allen Key, 5mm Allen Key, 4mm Allen Key, 3/16mm Allen Key, Thermal Grease (1g)
The matching X-MIXR shaker for mixing the X-Gamer X-Tubz ! The X-Gamer logo clearly adorns the sturdy plastic container with lid and drinking opening, so that the gamer equipment is safe from liquids even during heated battles. The volume of 500ml is more than sufficient for a daily requirement of the isotonic beverage powder. Technical data: Dimensions: 200 x 70 mm (H x W) Weight: 84 g Volume: 500 ml Colour: Transparent (container), Weiß (lid)
Alphacools HardTube family does get an additional sibling. The new HardTubes made out of borosilicate glass certainly bring a new level of quality into every system. The previous method that has been most commonly used for water cooling systems is normal PVC hoses - now Alphacool introduces a new approach to water cooling. The Alphacool HardTube additionally brings more tidiness into the system which enables a further structured impression. Borosilicate glass ticks every box on the checking list for watercooling systems. Stability and a brilliant appearance are not the only qualities that should lead to chosing this glass as even most chemicals and temperature flactuations can not harm the borosilicate glass. The whole chemical industry is depending on this glass and we can certainly say that this is not without reason. All glass tubes are compatible with the Alphacool HardTube connectors. Alphacool currently offers two classical sizes. One tube with a 16mm outer diameter and another with 13mm outer diameter. Further different length with 90° angles are introduced as its not possible to personally deform these tubes. To cut the tubes for the preferred length Alphacool recommends using a diamand cutting disc for the Dremel®.(Additionally availaible in our product line: Diamant cutting disc - Art.No: 1012316, Dremel® - Art.No: 32196 and 32229) The following options are available: HardTube borosilicate glass 13/10mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 13/10mm 40cm and 60cm HardTube borosilicate glass 16/11mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 16/11mm 40cm and 60cm Scope of delivery: 1x HardTube borosilicate glass 16/11mm 60cm WARNING:Do not under any circumstances use the usual glass tube cutter to shorten the borosilicate glass tube. Borosilicate glass is a solid glass which can not be cut properly with a normal glas tube cutter. Please refer to a Dremel® with the needed cutting disc. Note:Due to the made-to-fit pipes, the connections must be plugged straight with a little effort. Attention:This article is not compatible with Monsoon fittings. Der8auer: Extremely Expensive Hardtubes and DIY Glass-Cutter
EK-Quantum Magnitude Accent - Black is an interchangeable aesthetic inner frame for EK's new Magnitude water block. This black accent is best used on Magnitude water blocks with translucent tops where the LED’s shine inwards, or for those without LED implementation. This Magnitude accent is made of anodized aluminum. Available in several different colors and materials, these accent frames are compatible only with EK-Quantum Magnitude CPU water blocks Made in Europe - Slovenia!
The connection for 16mm (AD) Hard Tubes from EK Water Blocks, is a compression fitting made of nickel-plated brass. It is silver in colour and comes from the Torque series, which convinces with a simple and timeless design. Originally intended for the EKWB Quantum series, this fitting is also compatible with other EK products. In this fitting, the union nut serves as a compression ring, which presses the sealing ring onto the hard tube. It thus offers a higher level of safety and sealing than, for example, the fittings of the EK-HD series. As a small feature, the union nut has a recess under which coloured rings are placed, which provide a bit of individuality and are available separately. Technical Data: Material: Nickel-Plated Brass Colour: Silver Supported Tube: 16 mm OD Thread: G1/4", male Thread Length: 4,5 mm Outer Diameter (Fitting): 24 mm Installed Height: 15 mm Compatible Solid Tubing: Acrylic, PETG, Copper, Brass, Stainless Steel
EK-Quantum Vector TRIO RTX 3080/3090 Active Backplate - Acetal ist eine hochmoderne Ergänzung der EK® Quantum Line. Sie ergänzt die bestehenden EK-Quantum Vector TRIO RTX 3080/3090 Wasserblöcke und kühlt aktiv die Rückseite aller MSI® TRIO und SUPRIM GeForce RTX™ 3080 und 3090 GPUs. Die EK-Quantum Vector TRIO RTX 3080/3090 Active Backplate wird mit einem neuen Anschluss geliefert, der den serienmäßigen Anschluss des Vector Wasserblocks ersetzt und den Wasserblock und die Vector Active Backplate zu einer Einheit verbindet. Auf diese Weise benötigt das gesamte Gehäuse nur einen Zu- und einen Abfluss, wodurch unnötige zusätzliche Schläuche entfallen und das Durcheinander reduziert wird. Es ist die ultimative ästhetische und leistungsfähige Lösung, bei der Ihre GPU zwischen zwei Wasserblöcken eingebettet ist, was eine maximale Kühlung ermöglicht. Technische Spezifikation: Abmessungen: (LxHxB) - 307x153x38mm Lieferumfang: EK-Quantum Vector TRIO RTX 3080/3090 Aktive Backplate - Acetal Erforderliche Befestigungsschrauben, Muttern und Unterlegscheiben 1x vernickelter Messingstecker G1/4" EK-Loop Multi Inbusschlüssel (6mm, 8mm, 9mm) Thermische Pads
Reservoir diameter: 60mm Reservoir free volume: ~205mL Overall unit height: 160mm Mounting hole pattern: 50x50mm D-RGB connector standard: 3-pin (+5V, Digital, Blocked, Ground) Enclosed: EK-Quantum Kinetic TBE 160 DDC PWM D-RGB Mounting mechanism PLEASE NOTE: This product should NOT be installed with any aluminum Fluid Gaming parts! These units DO NOT come with a pump
The Protium expansion tank from Singularity Computers is a 100mm tube with a diameter of 60mm. Together with the acrylic attachments, the expansion tank reaches a height of 139mm. The tube itself is made of acrylic and has a total of seven G1/4" ports. Technical Data: Dimensions: 60 x 60 x 139 mm (L x W x H) Diameter: 60 mm Material: Acrylic (lid, base, reservoir), Aluminium (retention rings) Color: Black, Transparent Threads: 7x G1/4" Scope of Delivery: 1x 100 mm acrylic reservoir 2x Aluminium retention rings 1x 90° quad port cap (bottom) 1x Triple port cap (cover) 1x 16 mm internal acrylic flow standpipe 5x G1/4" stop fittings 2x Silicone O-rings
EX2-755 is an ambient liquid cooling system with several control options. This model contains a dual x 120mm fan aluminum radiator, providing roughly 590W of cooling with a 25°C ambient delta. Just add tubing, fittings, coolant, and connect to your cold plate(s).- Cooling capacity: 590W (2013BTU/hr) with 25°C liquid-ambient delta @ 4LPM- Radiator fan speed: automatic based on temperature, or 10 manual levels- Pump: 10 manual speed levels, up to 4LPM (1GPM)- Adjust audio alarm based on 3 included temperature sensors- Relay trigger can be configured as NO or NC and adjusted based on temperature- Power input: 12VDC (via computer Molex plug), or 110/220VAC with separate adapter- Reservoir capacity: 157ml (5.3 fl oz)- G 1/4 BSPP threads on back for fittingsVentilaatorJahRadiaatorJahJahutusvedeliku maht0,157 lVentilaatorite arv2 ventilaator(id)Kogus1Pumba pinge12Radiaatori materjalAlumiiniumToote värvMustKaal3,63 kgVentilaatori läbimõõt12 cm
- True Hi-Flow Design.- Hi-Quality Brass Material.- High Durability Nickel Finished In Carbon Black Color.- Hiding O-Ring Design.- The Best Choice Of Water Cooling Temperature Sensor In Stop Fitting Design.Toote värvMust
