Jahutid ja lisad

Aqua Computer Inline temperature sensor G1/4" - 60cm (53218)

RGB LED ring for reservoirs, inner diameter 60 mm, proprietary 4-pin connector for RGBpx components from Aquacomputer, compatible with D5 NEXT and QUADRO, Attention: This LED ring works exclusively with RGBpx components from Aquacomputer

The cuplex kryos NEXT marks a new milestone in CPU water block development. Every detail has been analyzed, optimized and tested to achieve perfection in cooling performance, installation procedure and product features. The result is not just a CPU water block with outstanding performance - it is a product series with various models differing in color and functionality. The VARIO models are the first CPU water blocks globally to incorporate a real-time adjustable base - never before has it been possible to adjust the geometry of a CPU block to perfectly fit the CPU while the PC is in operation. Models with VISION module are equipped with modern electronics: High resolution OLED display, integrated water temperature sensor and USB interface are just three of the features.Base part with micro structureThe base part of the cuplex kryos NEXT is equipped with an extremely fine micro structure, the structural width is lower than 200 µm. The coolant is injected centrally through a slot-shaped nozzle and then runs to both sides of the structure. The base itself is manufactured from copper, nickel plated copper or .925 sterling silver depending on model.Retention systemThe cuplex kryos NEXT retention system consists of 2.5 mm thick stainless steel plates equipped with nickel plated spring cups. Springs and knurled screws secure the water block on the motherboard, the retention system has a very clean look when installed. All retention system versions feature a mechanical stop for optimum clamping force and even force distribution. The knurled screws can be installed by hand, additionally a hexagon socket wrench can be used for easy installation.Water blocks for socket 115x or AM3 include a steel back plate with silicone insulation to stabilize the CPU region of the motherboard. Socket 2011 or AM4 motherboards already include a back plate as part of the CPU socket, therefore no additional back plate is required.For optimum performance, every cuplex kryos NEXT ships with outstanding thermal compound. A syringe with 0.5 grams of Thermal Grizzly Kryonaut is included, complete with plastic spatula. This compound has a high thermal conductivity and spreads out thin and evenly between CPU and water block due to its low viscosity. The amount is sufficient for approximately five applications.Color variantsThe top part of the water block is available in various materials and coatings:Acetal black: Shiny black high-tech plasticAcrylic glass: Transparent body suitable for illuminationCopper: Reddish glossNickel plated brass: Bright metallic glossPVD plated brass: High quality multi layer coating, dark metallic glossMaterial combinationCopper/copper: Top part copper, base copperTechnical detailsDimensions: Socket AM4: 111 x 75 x 22 mm (not including screws)Connection threads: G1/4Distance between threads: 24 mmScope of delivery Water block Mounting material (screws, springs, etc.) Thermal compound Thermal Grizzly Kryonaut, approx. 0.5 grams in syringe Plastic spatula Instruction manual

RGBpx LED ring for aqualis 100/150, 10 addressable LEDsThe RGBpx-compatible LED ring for aqualis 100 and aqualis 150 expansion tanks with a total of 10 individually addressable LEDs. The LEDs are mounted in a black rubber ring which is slid onto the glass tubes of the aqualis 100 and aqualis 150 expansion tank series.To operate the LED strip, an appropriate control unit with RGBpx output is required (not included in delivery). At the end of the strip there is an additional connector to connect another RGBpx component.Technical data: Inner diameter 50 mm Dimensions approx. 60 x 62 x 10 mm 10 individually controllable LEDs Scope of delivery: RGBpx LED ring one RGBpx connection cable, length 50 cm Compatible to: D5 NEXT QUADRO fan controller

Now finally also with us the Black ICE Nemesis radiators. The Black Ice® Nemesis® GTS radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using

PCI Slotblende mit zwei G1/4-Zoll-Innen-Gewinden

The cooling units from Hailea have been used in trusted waterchillers from other manufacturers for over 15 years. The new heat exchangers of the Ultra series are made from titanium. Therefore the chillers are perfect for watercooling systems. Another positive aspect about the Hailea units is the low noise emission. The pricing of the new series is also pleasantly affordable. New revision: New cool design More robust materials for even longer lifespan Lowered noise emissions Suitable for continuous operation Noise emissions: The small chillers (like HC150) have a noise emission of 20dB(A) only and can be used near the computer / aquarium without disturbing. Bigger models (like HC500) should be additionally decoupled to reduce the noise level if necessary The models HC1000 und HC 2000 should be extra decoupled or maintained in a seperate room. This waterchiller basically replaces the radiator as the coolant is chilled to the desired temperature by this unit. Temperatures down to 4°C are possible, please note that at low temperatures (high temperature difference) condensate may accumulate. Suitable insulation accessories are also available in our shop. Alternatively the coolant temperature can be set to just below room temperature to avoid this problem. Thanks to the low temperatures incredible overclocking potential is available! The lifespan of the components is extended by multiples. This system is also great for no-noise applications as the chiller can be located in another room. We recommend integration of the chiller into the cooling loop in combination with a radiator. This allows use of the chiller when required (overclocking, Benchmarks, summer etc..) and use of the radiator during normal operation. To estimate the required cooling performance here some non-binding estimates. The exact thermal emissions can be requested from the manufacturer of the hardware. CPU: 80W (standard) to 150W (overclocked) GPU: 50W (small cards) to 250W (current models such as GTX 980) MB: 20 to 40W per component The added values of your system must not exceed the given cooling capability of the chiller. What aquarium size can be cooled with my water chiller? The manufacturer provides the following data: Model / aquarium size in liters: HC-130 / 50-100L HC-150 / 50-200L HC-250 / 100-300L HC-300 / 100-400L HC-500 / 200-800L HC-1000 / 300-1000L HC-2000 / 400-1500L We at Aquatuning wish to advise you that the manufacturer’s data was obtained under optimal circumstances. The temperature response of the aquarium may greatly vary because of insulation, heat from lights respectively sunlight. Hence we recommend using the larger model when reaching the upper limit of the aquarium size values. Notes regarding shipment: For shipping via parcel delivery (GLS) we have manufactured a specially padded carton. For handling and packaging we must charge 15€ incl. VAT. This charge is not charged when the Chiller is picked up or with pallet shipment if the chiller is shipped without the special packaging. Note regarding shipping: This unit can only be shipped via a forwarding company. As the chipping charges differ by distance an online calculation is not possible. Please provide your full telephone number and E-Mail address when ordering, we will contact you after the order is complete. The shipping charge is approximately 50€ within Germany. Technical specifications: Power: 1/2 PS Power consumption: 375W Cooling capacity: 790W (suitable for extreme OC and cooling) Recommended coolant flow: 1200-3000 l/h Weight: 22kg Cooling agent: R134A Dimensions: 475x360x490mm (LxWxH) Connector outside diameter: 20-22mm Heat exchanger material: Titanium max. compressive load: 0,8bar Temperature adjustments: Digital read-out (precision 0,1°C), temperature setting in 1°C steps current demand: 2.4 A (50 Hz) current drain: 552 W Scope of Delivery 1x Waterchiller Hailea Ultra Titan 1500 2x 90° angle with rubber seal 2x straight with rubber seal 2x suitable hose clamps Note for first-time users: If you should have problems with your chiller please contact us before returning the chiller to us. In most cases there is no actual problem with the chiller, but the functionality of the unit is not fully understood by the user yet. Please note the following: The compressor unit automatically switches itself on and off, if the temperature sensor is manipulated your warranty is void, the noise level or an allegedly not sufficient cooling performance are no reason for a reclamation. The chiller can only function properly if the cooling loop is equipped with a sufficiently powerful pump. If these facts are considered most reclamations can be avoided and you will greatly enjoy this product! Note for aquarium-use: The cooling performance is affected by the aquarium-lamp the reduced pump power due to filters and the thermal waste of the pump. We therefore recommend to order the ciller at least on power-lever higher that theoretically calculated This product has been reviewed for you (by): Overclockingstation Zockon bit-tech (engl.) How2 (Userreview): Hardwareluxx

Kompletter Ersatz-Befestigungssatz für die XSPC DDC Photon 170 Reservoir-/Pumpen-Kombination inkl. Entkoppelung

Schwarzer LED-Lüfter von Raijintek im 2er Set, 120-mm-Format, 1.200 Umdrehungen pro Minute, max. 67,62 m³/h Fördervolumen, max. 0,61 mmH2O statischer Druck, LED-Ring mit RGB-Beleuchtung

With the Alphacool XPX Aurora Pro Eisblock, Alphacool offers a CPU water cooler specially designed for processors with particularly large processor cores. These currently include the AMD Threadripper models and processors from Intel for the LGA 2066 socket and the LGA 3647 server socket in narrow ILM design. As a CPU cooler from the Aurora Design line, the CPU cooler naturally offers integrated digital aRGB lighting. Extremely powerful The cooler base has been specially optimized for the large processor cores. With an area of 42 x 58.6 mm and 147 cooling fins the cooling area has been significantly increased. As a comparison, an Alphacool XPX Aurora Eisblock has 81 cooling fins to completely cover the processor core of a normal CPU. Both coolers use the same fin type with a thickness of only 0.2 mm. This clearly shows how far Alphacool has gone to offer the best possible performance. The entire cooler base is of course made of nickel-plated copper and not aluminium. This is due to the increased thermal conductivity of copper. It is almost twice as high as that of aluminium. How is the CPU cooler illuminated? As with all new Eisblock CPU water coolers, Alphacool relies on an integrated aRGB solution. An aluminium frame is flush with the CPU cooler. Of course, the aluminium does not come into contact with the water. The LED frame contains up to 14 addressable digital RGB LEDs. This is more than enough to illuminate the entire cooler even and brightly. The intensity of the illumination can of course be controlled by an appropriate controller. Due to the use of digital RGB LEDs, all known effects can be created, because each LED can be controlled separately with the right controller. The Alphacool Eisblock Aurora Pro cooler can also be connected and controlled via the 3-pin 5V connector on any compatible mainboard. The cable also has an integrated Y-adapter. This makes it easy to connect further Alphacool Aurora products in series without having to order separate Y-adapters. Only additional extension cables may be needed if you want to connect the products in series. Is the assembly difficult? Installation is child's play. Remove the protective film from the base of the cooler, apply some of the enclosed thermal paste to the CPU and then attach the cooler to the board. Depending on the base, the mounting screws are either screwed on before or after mounting. No tools are necessary for the assembly. Alphacool uses knurled screws, which allow a quick and easy assembly. Finally Plexi! The Alphacool Eisblock XPX Aurora Pro is the technical brother of the Eisblock XPX Pro 1U cooler, which was developed especially for the use in server housings. During the development the functionality had a much higher priority than the design, which was kept practical and discreet. The Eisblock XPX Aurora Pro has been optically adapted to the Aurora products and now offers the same design features as you are used to from the Aurora series. This allows you to perfectly match your entire system to each other optically and you don't have to make any compromises. Thanks to the plexiglass look, you can see the water flow beautifully. On the Plexi there is a black frame embedded with a very discreet Alphacool logo in one corner. Technical details Dimensions (WxTxH): 79 x 63,8 x 31 mm Net weight: 545 g Max working temperature: 60 °C Material cooler: nickel plated copper Material bottom part: brass Material top: Plexi Threads: 2 x G1/4“ Power supply Digital RGB: 3-Pin 5V Pressure tested: 1,5 Bar Certificates: CE, FC, ROHS Compatibility Intel: 2011 / 2011-3 / 2066 / 3647 Compatibility AMD: TR4 / TRX40 Download manual PDF: Alphacool Eisblock XPX Aurora PRO - Plexi Chrome Digital RGB Download data sheet PDF: Alphacool Eisblock XPX Aurora PRO - Plexi Chrome Digital RGB

DEMCiflex Dust Filter 200mm Round Black DF0020Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 180 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): Ø approx. 200 mmSize (filter): Ø approx. 175 mmCompatibility: 180 mm fan slotMaterial (filter): polyester meshColor: black (frame), black (filter)Assembly: mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric

Air flow 47.2 cfm, Noise level, max 30 dB, Dimensions 120 x 120 x 25mm, MFL-B2DN-18NPA-R1

Standard Fan-Grill für 92mm Lüfter in Schwarz

Silberner Staubfilter aus Aluminium für 92mm Lüfter

Antivibrations-Rahmen für 80mm-Lüfter - UV-aktiv

Antivibrations-Rahmen für 80mm-Lüfter

Filterkassette aus Kunststoff für 120x120mm Lüfter gegen Einstauben von Lüftern, Kühlern und Gehäusen

Filterkassette aus Kunststoff für 92x92mm Lüfter gegen Einstauben von Lüftern, Kühlern und Gehäusen

DEMCiflex Dust Filter 120mm Round Black/White DF0525Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): Ø approx. 138 mmSize (filter): Ø approx. 113 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric

Alphacool Eisbaer Intel replacement mounting.This bracket is the same as the one included in the original Alphacool Eisbaer set. Intel 1150/1151/1155/1156, Intel 1366, Intel 2011, Intel 775, Intel 2066, Intel 2011-3 Scope of Delivery 1x Alphacool Eisbaer Intel mounting with backplate and screws

With the “Eisbaer” Quick-Connect Extension Kit, expanding an “Eisbaer” or “Eiswolf” GPX-Pro cooler loop with additional components is simple. For example, it’s easy to add another radiator, an additional cooler or any other components. The kit consists of two 32cm-long hoses in 11/8 format, encased in anti-kink springs. This prevents bending in the hoses, and thereby prevents interruptions to the flow of water. Safety is our top priority. Two ends have 90° angled pieces, pre-installed on the hoses. The only thing you need to do is screw these into the corresponding G1/4” threads. On the other end are the ends of two quick-release safety locks from the Alphacool HF series, just like the ones found on the “Eisbaer” or “Eiswolf”. That means all you have to do is open the quick-release locks on the “Eisbaer” or “Eiswolf” and screw them together with the corresponding parts in this kit and an additional product for extension, and your loop is complete - after it’s been filled, of course. For that, this kit includes a squeeze bottle with 250mL of osmosis filtered water. With the squeeze bottle, the loop can easily be filled at the designated spots. On the “Eisbaer”, for example, this would be the fill port on the “Eisbaer” cooler. Technical Details: tubing length: 32cm Material Quick Connector: Nylon Colour: Black G1/4" Threads tubing size: 11/8mm Pre-filled: 250ml osmosis water Scope of delivery: Alphacool Eisbaer Quick-Connect Extension Kit

Deep, intense colors, pleasant handling and easy installation were the goals when developing this tubing generation. The result is a great choice of sizes and colors such as red, green, blue or black.When designing these tubes, one goal was to make colored coolant and hence the strain from coloring particles on the cooling loop obsolete. With these tubes the color comes from the tubes themselves.Besides color, the installation and kinking properties are always an important factor when choosing tubing. Tight bending radiuses and easy handling in tricky situations were also taken into consideration during development. Hence the plastic mixture was developed to perfection and we have created tubing which manages to combine usually opposing properties to please both beginners and advanced users. Manufacturing in Germany promises permanently high quality. The manufacturing with years of experience ensures the best product all of the time!Technical specifications:Material: PVCColor: UV blueInner diameter: 10mm, 3/8“Outer diameter: 13mm, ½“Wall thickness: 1,5mm, 1/15“Extent of delivery:1x Alphacool Schlauch AlphaTube HF 13/10 (3/8"ID) - UV Blau 3m (9,8ft) Retailbox

Alphacool Hose AlphaTube HF, 13/10mm, 1m, transparent (18528)

Alphacool Christmas tree connectors 1/4" - 16/10mm, 6 pcs Silver (17235)

Alphacool Christmas tree connector 1/4 "- 16 / 10mm, black (17232)

Alphacool 1/4" coupling, Chrome (17255)

Alphacool NexXxos ST30 Full Copper 240mm (1011657)

Alphacool Water main 1/4" - 16mm, for GTX titan (17196)

Alphacool 1/4" coupling - 16/13 mm, Chrome (17195)

The HardTube Project is becoming a reality. Alphacool is setting out on a new path and making great strides! Before now, the most common approach to water cooling was to use normal PVC tubes – now Alphacool is offering a new way to configure your water cooling system. The HardTube variants bring more order into your system, which gives off a more structured impression. The newest are the brass tubes, available in black chrome and chrome, as well as acrylic tubes, carbon, and borosilicate glass. With their fitted connectors and simply-designed functionality, they can be connected to each other with an absolutely tight seal. The PETG-tubes can be bent with the appropriate bending tools in order to fit into any system easily, without needing any additional angled pieces. In order to install the tubes into the system, they need to be sawn to the correct length. PETG tubes can be bent at lower temperatures than acrylic and are generally more flexible and easier to handle. Technical Details: Material: PETG Length: 60cm Scope of delivery: 1x Alphacool Eisrohr 13/10mm PETG 60cm - 4pcs

The new generation of Alphacool NexXxoS radiators, a name that is known for experience and quality, is here to breathe new life into the radiator market!Everyone who uses watercooling needs a radiator, and everyone has different requirements for the heat exchanger. Naturally, consumers want the product that's best in class. The Alphacool NexXxoS radiators are here to challenge the best in their class, and be crowned the best radiators in every area and size. No more back and forth - with Alphacool NexXxoS radiators, you know what you're getting!Alphacool has been a trendsetter on the scene for developing and improving radiators for years. That's why these models are among the first radiators to really earn the descriptor "full copper"! All the main elements, not just the fins and channels, but also the channel heads are made of copper. Material-wise, this is a big advantage, and one where other radiators fall by the wayside. The Alphacool NexXxoS X-Flow radiators set themselves apart significantly from conventional radiators in their construction. The X-Flow radiators are built for high flow rates. The slanted copper chambers on either side are built identically. This means the water can flow through all the channels at the same time until it flows into the opposite chamber and leaves the radiator.Freedom in the installation is one of the central points on which Alphacool's development department focused. Both copper chambers have three 1/4" threads. That means connections can be attached on the top, bottom and at the front or back (not on the NexXxoS ST30). Fewer angles are needed, which increases the flow rate and offers more options in the installation. Here, too, Alphacool carries the standard sizes of the 120mm series. Different strengths, 30mm, 45mm and 60mm underscore the wide spectrum that these radiators cover. The installation of the radiators, as well as the fans and radiator faceplates, is easy to do with this series: the M3 threads are standard in the radiator sector, affordable and available in all lengths.Even the dreaded mishap of turning the screws in too deeply won't lead to costly damage with this radiator: an inner protective edge stops the screw before it can come into contact with the fins.The fin spacing was chosen so that the radiator could reach its optimal cooling performance even with slow or medium-speed fans. This is not only comfortable in terms of background noise, but also puts no constraints on the choice of fans. All in all, it's where experience and powerful performance meet with a forward-looking approach and sophisticated solutions.Alphacool NexXxoS Radiators - the one tool for all your cooling needs! Tehchnical dataQuantity of cooling channels28Cooling channelsCopperColorblackFan threadM3SlatsCopperThickness39 - 49mmConnection2x G1/4"Fan size140mmNumber of fans2HousingSteelManufacturerAlphacoolFins per inch16Pressure tested0,8 bar

Alphacools's fittings go new ways in looks, quality of manufacturing, colours and choice. The inner diameter of these fittings truly deserves the „high flow“ attribute! The first three colours, Chrome, Deep Black and Shiny Copper offer something for every taste. The product matching series are designed to look elegant in every system, highlighting the individual design of the computer. The limits are endless with these Alphacool fittings in combination with Alphacool tubing! With a new process during chromatising the surface finish is completely connected with the brass body, hence ensuring permanent intense colours and peeling of the chrome layer. The Alphacool name in blue lettering on some of the fittings additionally underlines the individuality of these items. Functionality of this connector:A bushing with two 1/4“ inner threads comes in handy for the extension of fittings or for connection of a component with an outer thread to a fitting. Technical specifications:Material: Brass, chromatizedColour: Deep Black Dimensions:Length: 22mmWidth: D17mm Extent of delivery:1 x Alphacool HF socket 2 x G1/4 inner thread - Deep Black This product has been reviewed for you:ModdingbaseXtremesystems (Engl.) (userreview)PT-reviews (Pt)

Alphacools's fittings go new ways in looks, quality of manufacturing, colours and choice. The inner diameter of these fittings truly deserves the „high flow“ attribute! The first three colours, Chrome, Deep Black and Shiny Copper offer something for every taste. The product matching series are designed to look elegant in every system, highlighting the individual design of the computer. The limits are endless with these Alphacool fittings in combination with Alphacool tubing! With a new process during chromatising the surface finish is completely connected with the brass body, hence ensuring permanent intense colours and peeling of the chrome layer. The Alphacool name in blue lettering on some of the fittings additionally underlines the individuality of these items. Functionality of this connector:A double nipple with two 1/4“ outer threads is very useful for the extension of fittings or connection of components with an inner thread to a manifold or similar components with an inner thread Technical specifications: Material: Brass, chromatizedColour: Chrome Dimensions:Length: 4mmWidth: D18mm Extent of delivery:1x Alphacool double nipple G1/4 outer thread to G1/4" outer thread with O-ring - Chrome This product has been reviewed for you:Xtremesystems (Userreview) (engl.)PT-Reviews (pt)

Dimensions 120x120x25mm, Revolutions 650-1800rpm, Air throughput 105.3m³ / h, Air pressure 2.5mmH₂O, Volume 8-27dB (A), Fan bearing simple plain bearing, Voltage range 12V, Power consumption 1.8W, Connection 4-pin PWM, 3-pin ARGB (+ 5V / DATA / GND), RGB lighting, Special features LED control, MFX-B2DN-183PA-R1

Internal type (closed system), Heat sink CPU, Heat sink material copper, Compatibility CPU 1150, 1151, 1155, 1156, 1200, 1366, 2011, 2066, AM2, AM2 +, AM3, AM3 +, AM4, FM1, FM2, FM2 +, TR4, Radiator size 240mm, Radiator thickness 27mm, Radiator material aluminum Fan 2x 120mm, 700-1800rpm, 18-30.2dB (A), 118.9m³ / h, 12V pump, TDP classification 300W, Special features LED (RGB), XC977

Internal type (closed system), Heat sink CPU, Heat sink material copper, Compatibility CPU 775, 1150, 1151, 1155, 1156, 1200, 1366, 2011, 2011-3, 2066, AM2, AM2 +, AM3, AM3 +, AM4, FM1, FM2, FM2 +, TR4, sTRX4, SP3, Radiator size 360mm, Radiator thickness 27mm, Radiator material aluminum, Fan 3x 120mm, 500-2000rpm, 14.3-34.3dB (A), 36.8-133.8m³ / h, 0.23-2.39mmH₂O, 12V pump, Connections G1 / 4 ", Special features LED (RGB), LED control,