Teltonika FMB910 is a low-cost version of the FMB920 tracker. The main differences are the overall size of the device different GNSS antenna design and some components being bigger in size thus the change in dimensions. The device has all internal antennas that ensure easy installation with no need to wire the antennas. Like other Teltonika trackers FMB910 is assembled by robots which eliminates human error and ensures high quality of the device. The tracker has a digital input to monitor ignition or to connect an alarm button. Vehicle remote immobilizing may be achieved using a digital output. Bluetooth connectivity expands peripherals’ connectivity even more. Teltonika FMB910 can be used in a variety of applications like basic track and trace or recovery of stolen vehicles. It can be installed in light vehicles motorbikes and even trucks.
Newly introduced FMC125 is a small ADVANCED series device with 4G (LTE Cat 1) network coverage including 3G (UMTS) 2G (GSM) fallback compatibility. Device equipped with GNSS/Bluetooth and LTE modules internal GNSS and LTE antennas. FMC125 developed on the existing Teltonika FMB platform therefore it keeps all of the functionalities from FMB125 and builds on top of them with its industry-leading connectivity coverage.Device is designed for communication with various third party RS232 or RS485 devices like digital fuel sensors (LLS) Garmin navigation device RFID reader and much more. It is also excellent for refrigerated transport because it has extended input/output set and 1-wire interface for temperature monitoring. The Dual-SIM feature provides a backup communication channel where the coverage of a singular operator is not sufficient. As well Dual-SIM feature will let you significantly reduce roaming costs.
Carbon monoxide sensor KID-2030DCR2030-DCR carbon monoxide sensor equipped with a KIDDE electrochemical sensor, guaranteeing up to 10 years of operation. Battery power supply allows the detector to be installed in an optimal place in the room and also provides protection in the event of a power supply disappearance on the network. Exceeding the permissible level, which is signaled optically (red LED) and acoustically (loud, pulsating sound alarm with a power of 85DB). The device's memory saves information about detection of a concentration of which exceeding the level of 100 ppm. Thanks to this, the user can make sure that during his absence in the room there was no carbon monoxide emission. The sensor has a test / reset button to check the operation of the device and reset the alarm signaling. The efficiency control system monitors on an ongoing basis, among others: sensor, internal circuits and battery condition. In the case of incorrect operation or low battery charge, the yellow LED light flashes and the warning sound signal is turned on. In addition, the sensor has been equipped with a function that allows you to quickly check the correct sensor response to the CO test gas. Thanks to a specially designed housing, in addition to mounting on the wall, the sensor can also be placed on a flat surface, e.g. on a bedside table near the bed. 10 years after activating the power supply, the sensor will remind you of the need to replace the device. 2030-DCR is marked with a construction mark B confirming the fulfillment of the requirements of the Polish standard PN-EN 50291-1: 2018+AC: 2021 for homemade carbon monoxide detectors. The research was carried out by the Scientific and Fire Protection Center-State Research Institute Józef Tuliszkowski (CNBOP-PIB). In addition, it has a certificate confirming the fulfillment of the requirements of the BS EN 50291-1: 2018 standard issued by the independent research single Tüv Rheinland.
"2N® Helios IP Verso turvasidesüsteemi saab konfigureerida vastavalt teie vajadustele, kuna see on modulaarne. See pakub usaldusväärset juurdepääsu kontrolli ja võimaldab lihtsat ühendamist teiste süsteemidega, tagades seega veelgi suurema turvalisuse rajatisele.Nüüd saadaval ka Bluetooth-mooduli või puuteekraaniga. Pinnale paigaldatav raam, 2 moodulit.
